Volume 15, Issue 1, May 2015, Pages 175–179
Prof. L.P. Bhambre1, Nikita V. Shejval2, Priyanka S. Patil3, and Poonam C. Jadhav4
1 Asst. Professor, Department of ETC, SVIT, Chincholi, Nashik, (M.S), India
2 Electronics & Telecommunication Engg. Dept., Sir Visveswaraya Institute Of Technology, Chincholi, Nashik, (M.S), India
3 Department of electronics and telecommunication engineering, faculty of science, savitribai phule university, India
4 Electronics & Telecommunication Engg. Dept., Sir Visveswaraya Institute Of Technology, Chincholi, Nashik, (M.S), India
Original language: English
Copyright © 2015 ISSR Journals. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
A new generation of industrial electrical furnace has been developed during the last 25-30 years. Present practices followed in electrical furnace are discussed in this paper. Through a literature review accounts of various practices present being followed in steel industries using electrical furnace has been carried out in few industries in India.
The Furnace control which is the most important part of any steel plant. Microcontroller is also used measure furnace temperature by using sensor (PT100). In Automate a steel plant we can monitor the furnace temperature and minimize human intervention.
Steel plants require continuous monitoring and inspection at frequent intervals. The objective of the proposed work is to develop steel plant. We can continue monitor the furnace and observe/see the overview of the system seen on the PC.
In our project we can also work properly billet cutting billet cutting of metal rod are properly.
Author Keywords: Electrical Furnace, Billet Cutting, Molten Metal, Billet Counting.
Prof. L.P. Bhambre1, Nikita V. Shejval2, Priyanka S. Patil3, and Poonam C. Jadhav4
1 Asst. Professor, Department of ETC, SVIT, Chincholi, Nashik, (M.S), India
2 Electronics & Telecommunication Engg. Dept., Sir Visveswaraya Institute Of Technology, Chincholi, Nashik, (M.S), India
3 Department of electronics and telecommunication engineering, faculty of science, savitribai phule university, India
4 Electronics & Telecommunication Engg. Dept., Sir Visveswaraya Institute Of Technology, Chincholi, Nashik, (M.S), India
Original language: English
Copyright © 2015 ISSR Journals. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Abstract
A new generation of industrial electrical furnace has been developed during the last 25-30 years. Present practices followed in electrical furnace are discussed in this paper. Through a literature review accounts of various practices present being followed in steel industries using electrical furnace has been carried out in few industries in India.
The Furnace control which is the most important part of any steel plant. Microcontroller is also used measure furnace temperature by using sensor (PT100). In Automate a steel plant we can monitor the furnace temperature and minimize human intervention.
Steel plants require continuous monitoring and inspection at frequent intervals. The objective of the proposed work is to develop steel plant. We can continue monitor the furnace and observe/see the overview of the system seen on the PC.
In our project we can also work properly billet cutting billet cutting of metal rod are properly.
Author Keywords: Electrical Furnace, Billet Cutting, Molten Metal, Billet Counting.
How to Cite this Article
Prof. L.P. Bhambre, Nikita V. Shejval, Priyanka S. Patil, and Poonam C. Jadhav, “Furnace Monitoring and Billet Cutting System,” International Journal of Innovation and Scientific Research, vol. 15, no. 1, pp. 175–179, May 2015.
